MAX2769B
Universal GPS Receiver
Preconfigured Device States
When a serial interface is not available, the device can
be used in preconfigured states that don’t require pro-
gramming through the serial interface. Connecting the
PGM pin to logic-high and SCLK, SDATA, and CS pins
to either logic-high or low sets the device in one of the
preconfigured states according to Table 3 .
Power-On Reset (POR)
The MAX2769B incorporates power-on reset circuitry to
ensure that register settings are loaded upon power-up.
To ensure proper operation, the rising edge of PGM must
occur no sooner than when V CC_ reaches 90% of its final
nominal value; see Figure 4 for details.
Table 3. Preconfigured Device States
Serial Interface, Address, and
Bit Assignments
A serial interface is used to program the MAX2769B for
configuring the different operating modes.
The serial interface is controlled by three signals: SCLK
(serial clock), CS (chip select), and SDATA (serial data).
The control of the PLL, AGC, test, and block selection
is performed through the serial-interface bus from the
baseband controller. A 32-bit word, with the MSB (D27)
being sent first, is clocked into a serial shift register when
the chip-select signal is asserted low. The timing of the
interface signals is shown in Figure 5 and Table 4 along
with typical values for setup and hold time requirements.
DEVICE ELECTRICAL CHARACTERISTICS
3-WIRE CONTROL PINS
0
1
2
3
4
5
6
7
16.368
16.368
16.368
32.736
19.2
27.456
16.368
27.456
16
16
16
32
96
26
16
26
1536
1536
1536
1536
7857
1488
1536
1508
I
I
I
I
I
I
I
I
1
1
2
2
2
3
3
3
Differential
Differential
CMOS
CMOS
CMOS
CMOS
CMOS
CMOS
4.092
4.092
4.092
4.092
4.092
4.092
4.092
9.27075
2.5
2.5
2.5
2.5
2.5
4.2
4.2
9.66
5th
3rd
5th
5th
5th
5th
5th
5th
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
V CC_
100%
90%
0%
PGM
PGM = 0
PGM RISING EDGE ANYTIME
AFTER V CC_ HAS REACHED
90% OF ITS NOMINAL VALUE.
TIME (s)
TIME (s)
Figure 4. V CC_ Power-On Reset
Maxim Integrated
17
相关PDF资料
MAX2769EVKIT+ KIT EVAL FOR MAX2769
MAX2821ETM+T IC TXRX 802.11B 2.4GHZ 48-TQFN
MAX2829EVKIT EVAL KIT MAX2828, MAX2829
MAX2830EVKIT+ KIT EVAL FOR MAX2830
MAX2831EVKIT+ KIT EVAL FOR MAX2831
MAX2837EVKIT+ KIT EVAL FOR MAX2837
MAX2838EVKIT+ KIT EVAL FOR MAX2838
MAX2839ASEVKIT+ KIT EVAL FOR MAX2839A WLP
相关代理商/技术参数
MAX2769BEVKIT# 功能描述:射频接收器 Eval Kit for MAX2769B Universal GNSS receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX2769E/W 功能描述:射频接收器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX2769E/W-GB6 功能描述:射频接收器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX2769E/W-T 功能描述:射频接收器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX2769E/W-TGB6 功能描述:射频接收器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX2769ETI+ 功能描述:射频接收器 Universal GPS Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX2769ETI+T 功能描述:射频接收器 Universal GPS Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX2769EVKIT+ 功能描述:GPS开发工具 MAX2769 Eval Kit RoHS:否 制造商:STMicroelectronics 产品:Evaluation Boards 工具用于评估:IT600, STM32F20x 频率:1.575 GHz 工作电源电压:1.8 V 接口类型:Wireless